Monday 15 July 2013

Paving the way....

One of the most important if understated visual elements in any urban game set in western Europe are pavements. Sure you can plonk your buildings down on a grey surface and be done but it lacks something.

Pavements provide definition in the urban scape. They give a clear distinction between highway and pedestrian  - road and built up. Expanding the footprint of  those terraced rows or high street shops, turning them into built up islands, they offer a psychological barrier, a movement channel, a mini objective.

They also host their own iconic urban gloss in the form of  lamp-posts, telephone boxes, rubbish bins and more.

I've been wrestling with getting the right pavements for Winter of '79. Card and paper just didn't seem to cut it. Finally I managed to hit on a solution thanks to an enterprising eBayer selling OO scale scenic moulds for £6.50 plus postage. And you can see the results for yourself when given the quickest of washes with GW's Nuln Oil.

I already had a carton of Woodlands Scenics Lightweight Hydrocal casting plaster, so thought 'I'll give it a punt for a few quid'. The mould arrived before the weekend allowing me to start a cottage industry churning out 80mm x25mm x2mm pavement section after section.

I have to admit that it was fun of sorts, but I had a day to spare so it was just a matter of being disciplined as you obviously have to wait for each batch to set and harden before you can make the next pair of pavements.

Each set took 5 minutes to mix and pour the Hydrocal. I used one heaped and one level teaspoon of Hydrocal mixed with two teaspoons of water using a wooden coffee stirrer. Nothing onerous there. Then laid to one side for a minimum of 40 minutes to set. I basically looked at it as an hourly task - returning each hour on the hour to cast a new batch.

So, what about the results? Well not surprisingly they got better with each attempt. Even so, you can see in the 'before' photo below that the best of the cast pavement sections still had enough of a rough edge that they will need to be smoothed off with an emery board. But this takes only seconds.It's exactly the same batch in both photos


So here's what I learnt after a few breakages for those of you who may be tempted yourself.
  • Place the mould on a flat surface. 
  • Handle the mould as little as possible once you've poured the mixture. It's flimsy and picking it up may weaken the structure of the casts once the Hydrocal starts to set.
  • With that in mind, don't hand around as the Hydrocal is only workable for about five minutes. 
  • Press the mixture down and into the nooks and crannies, then top up as required. 
  • Use the flat edge of your coffee stirrer to level the mixture to get a near perfect flat cast. 
  • Do all three casts then, clean round the edges with a damp tissue to reduce the cleaning required on the cast sections.
  • However much you are tempted now, leave it be for at least 40 minutes. 55 is better and more, better still.
  • To remove the cast sections turn the mould upside down on a flat surface with the corner piece facing you.  Now slowly peel back the mould. The corner piece is easy enough, it will drop out, but if a pavement section seems to be sticking just gently turn back the other end of the mould. That should be enough. DO NOT press or apply any pressure where the pavement sections are or they are likely to break.
  • Breakages - no big deal really. The breaks are usually very neat and come at joins of the paving slabs so you can seamlessly glue them together again. Worst comes to worst you have broken paving slabs for barricades, craters in the street etc.
  • Bubbles and miscasts? Some, though the faster you try to be with your mixing and pouring, or should that be 'lazy'. the worse it seems to be. On the most part they look like natural wear and tear and of course the road workers are on strike! Seriously, just use a blob of left over Hydrocal or whatever or hide/repair the worst or plant some weeds or leave a discarded newspaper or a Coke Can cut from a piece of  sprue if you are that bothered.
  • Left over Hydrocal gloop? Have some newly based figures on standby to avoid wastage. 
The Hydrocal is a VERY lightweight material. I am only using it as it's to hand and will 'paint' the cast pavement sections with PVA to strengthen them. I may try some smooth Polyfilla next to see what the results are. The Five minute stuff would be ideal if it worked.....

Alright then, want to try this for yourself? Check out eBay seller 087_odea.


Cheers
Mark

8 comments:

  1. Looks fantastic. I'll need to pick up some of these. Hopefully he does 28mm scale as well.

    ReplyDelete
    Replies
    1. A 28mm figure looks ok on these pavement sections.

      Cheers
      Mark

      Delete
  2. I like the look of those- cheaper than the Ainsty ones that I have been using too.

    Cheers,

    Pete.

    ReplyDelete
  3. Nice! I like the look of a good pavement to separate house or shop from street.

    ReplyDelete
  4. They look superb and wonderfully versatile, especially given the resurgence in all things Victoria at present.

    ReplyDelete
    Replies
    1. The seller also does a mould for cobblestones.

      Cheers
      Mark

      Delete
  5. Looks great, I've been doing MDF wrapped in the right texture but it does look rather flat compared to these!

    ReplyDelete
  6. Secret of stable moulds apparently is... LEGO!
    Make a small tray out of lego to sit your mould on/into
    Jon :)

    ReplyDelete